Expansion Of Range Research Articles

Adsorption and gas sensitive behavior of Co2+ doped TiO2(101) crystal planes

Density functional theory (DFT) and Electrochemical Impedance Spectroscopy (EIS) were used to study the molecular adsorption behavior of the Co2+ doped TiO2(101) crystal plane, and the ethanol molecular gas sensitivity test was performed. Theoretical models indicate that doping leads to oxygen defects on the crystal plane and further chemisorption of two oxygen molecules, resulting in reduced electrical conductivity and improved oxygen storage capacity on the crystal plane. Ethanol molecules do not compete with N2, O2, and H2O molecules on doped crystal planes because of their different adsorption active sites, which means that the response time of gas-sensitive detection of ethanol molecules is short and is not interfered with the air molecules in the test environment. These results were confirmed by EIS and gas sensitivity experiments. The change of electrical conductivity after the adsorption of molecules on the crystal plane was confirmed by EIS. The enhanced oxygen storage capacity of the doped crystal plane was confirmed by the expansion of the linear response range of gas-sensitive detection from 20-100 ppm before doping to 20–1200 ppm. This provides a scientific basis for effectively shortening the gas-sensitive response time, increasing the concentration range, improving the oxygen-carrying capacity, and enhancing the catalytic and gas-sensitive properties of the material.

Distribution models in invasive plants with climatic niche expansion: a case study of Ulex europaeus L. in Colombian Andes

AbstractInvasive plants have a wide distribution worldwide. Their ability to adapt and colonize different climates is attributed to the phenotypic plasticity and the expansion of the climatic niche of the species. Simultaneously, their distribution patterns will be affected by climate change, creating or reducing the ideal areas for their establishment. We evaluated the current and potential distribution of Ulex europaeus L. in Colombia, under the global circulation models ACCESS-ESM1-5 and MIROC6 in two scenarios, for the years 2041–2060, taking into account its climate niche expansion. An ecological niche model was built for this purpose using Maxent algorithm of the KUENM, the records of the species in native and invasive condition from the GBIF portal, and records obtained through field trips and bioclimatic variables from Worldclim2 were used. Changes in potential distribution were analyzed with the Biomod2. A total of 1072 occurrence records were found for U. europaeus and 109 records were found in Colombia in the Cordillera Central and Oriental, where an expansion of the altitudinal range was evidenced from 2000 to 4052 m above sea level. Climate change models for Colombia showed that the creation of new areas for potential establishment is less than 1% and there is a reduction in potential distribution of 12 and 31% due to unsuitable climatic conditions that would affect their germination capacity. However, given its potential for adaptation, the invasions will persist in the new conditions and will continue their colonization process at higher altitudes where they find optimal temperatures for their germination and establishment.

Double S-scheme Cu2−xSe/twinned-Cd0.5Zn0.5S homo-heterojunctions with surface plasmon effects for efficient photocatalytic H2 evolution

The enhancement of charge separation and utilization efficiency in both the bulk phase and interface of semiconductor photocatalysts, as well as the expansion of light absorption range, are crucial research topics in the field of photocatalysis. To address this issue, twinned Cd0.5Zn0.5S (T-CZS) homojunctions consisting of wurtzite Cd0.5Zn0.5S (WZ-CZS) and zinc blende Cd0.5Zn0.5S (ZB-CZS) were synthesized via a hydrothermal method to facilitate the bulk-phase charge separation. Meanwhile, Cu2−xSe with localized surface plasmon resonance effect (LSPR) generated by Cu vacancies was also obtained through a hydrothermal process. Due to their opposite electronegativity, a solvent evaporation strategy was employed to combine Cu2−xSe and T-CZS by intermolecular electrostatic. After optimization, the photocatalytic hydrogen (H2) evolution rate of 5 wt% Cu2−xSe/T-CZS reached an impressive value of 60 mmol∙h−1∙g−1, which was 4.6 and 66.6 times higher than that of pure Cu2−xSe and T-CZS, respectively. Furthermore, this composites demonstrated a remarkable rate of 0.46 mmol∙h−1∙g−1 under near-infrared (NIR) wavelength (>800 nm). The enhanced performance observed in Cu2−xSe/T-CZS can be attributed to its unique and efficient double S-scheme charge transfer mechanism which effectively suppresses rapid recombination of electron-hole pairs both within the bulk phase and at the surface interfaces; this conclusion is supported by Density Functional Theory (DFT) calculations as well as electron paramagnetic resonance spectroscopy analysis. Moreover, incorporation of Cu2−xSe enables effective utilization ultraviolet visible-near infrared (UV–Vis-NIR) light by the composites while facilitating injection “hot electrons” into T-CZS for promoting photocatalytic reactions. This study provides a potential strategy for achieving efficient solar energy conversion through synergistic integration of non-stoichiometric plasmonic materials with photocatalysts with twinned-twinned structures.

Internal electric field and oxygen vacancies synergistically boost S-scheme VO/BiOCl-TiO2 heterojunction film for photocatalytic degradation of norfloxacin

Sluggish interfacial dynamics and weak redox properties make the degradation of antibiotics by photocatalysts still a great challenge. Herein, constructing S-scheme heterojunction between BiOCl and TiO2 nanorod arrays (TNA) by hydrothermal method, and the synergistic effect of oxygen vacancies (VO) and Internal Electric Field (IEF) on improving the performance of the photocatalysts was revealed by adjusting the VO. The VO modified BiOCl-TiO2 (VBiTNA) exhibited excellent photocatalytic activities for norfloxacin, achieving a degradation efficiency of up to 90.2 % in just 60 min, and the rate constant was as high as 3.67 × 10-2 min−1. In addition, it also showed great photocatalytic degradation performance of NOR in a wide pH range, complex ionized water environment and real water source. The degradation intermediates and degradation pathway of NOR were predicted with LC-MS technology and Fukui function. Combined with free radical capture, electron paramagnetic resonance, relevant electrochemical testing, and DFT calculations reveals the mechanism of the enhanced photocatalytic performance of VBiTNA. The performance enhancement can be attributed to the expansion of the light absorption range, enhanced adsorption of O2 and effective activation to generate ·O2–, while improving the separation efficiency of electron-hole pairs and maintaining a strong redox capacity. This research focusing on VO and IEF mechanisms will help to advance the rational design of high-performance defective photocatalysts.

Predicting the impacts of urban development on urban thermal environment using machine learning algorithms in Nanjing, China

The urban thermal environment undergoes significant influences from changes in land use/land cover (LULC). This article uses CA-ANN and ANN algorithms to forecast LULC and changes in the urban thermal environment in Nanjing for the years 2030 and 2040. It investigates the interplay between LULC changes, land surface temperature (LST), and the urban thermal field variance index (UTFVI). The findings reveal that urban land exhibited a significant expansion trend from 2000 to 2019, reaching 1083.43 km2 in 2019. The forecast indicates that urban land may increase by 8.79% and 10.92% by 2030 and 2040, respectively. Conversely, vegetation and bare land may decrease. The LST is likely to continue to rise, accompanied by a significant expansion of the high temperature range and a contraction of the low temperature range. By 2030 and 2040, the area with LST<20 °C is likely to decrease by 2.17% and 3.19%, while the area with LST>30 °C is likely to expand by 5.68% and 8.08%, respectively. The UTFVI area of urban land may decrease at none and middle levels but may notably expand at stronger and strongest levels. The areas with UTFVI at none, weak, and middle levels show a declining trend, while the increase in UTFVI at the strong level may exceed 46.29% and the strongest level of UTFVI may continue to expand. This study offers new insights into urban sustainable development and thermal environment governance.

Expansion of the Distribution Range and Size of the Invasive Blue Crab on the Turkish Coast of the Black Sea

The blue crab (Callinectes sapidus Rathbun, 1896) is an euryhaline species originally native to the western Atlantic Ocean. However, it has expanded its range into the Black Sea, including the Turkish coastal waters. Blue crab specimens were sampled along the Black Sea coast of Türkiye, covering the stretch from Cape Taşkana to the Georgian border. The monitoring studies spanned the period from 2017 to 2024. Analysis of the 16 specimens revealed a carapace width range of 14.8 to 20.3 cm, with males exhibiting larger sizes compared to females. Notably, two of the sampled females were observed to be carrying eggs, highlighting reproductive activity in the region. This study also reports the discovery of the largest blue crab ever recorded on the Turkish coasts of the Black Sea, with a male specimen measuring 20.33 cm in carapace width and weighing 565.1 g. Additionally, a male specimen sampled in the Rize region suggests the species has expanded its range to the easternmost part of the Black Sea. The findings contribute significantly to our understanding of the distribution and growth potential of the blue crab in the Black Sea. The larger sizes observed in males and the presence of ovigerous females indicate successful adaptation and potential establishment of a self-sustaining population. As invasive species, blue crabs can significantly influence benthic communities and food chains, highlighting the importance of a prudent management approach to fisheries biology and ecosystem management

The Mediterranean Mussel Mytilus galloprovincialis (Mollusca: Bivalvia) in Chile: Distribution and Genetic Structure of a Recently Introduced Invasive Marine Species.

The genetic characteristics of invasive species have a significant impact on their ability to establish and spread. The blue mussel (Mytilus galloprovincialis), native to the Mediterranean Sea, is a leading invasive species of intertidal coasts throughout much of the world. Here, we used mitochondrial DNA sequence data to investigate the genetic diversity and phylogeographic structure of invasive (M. galloprovincialis) versus native (Mytilus chilensis) populations of blue mussels in Chile. We evaluated whether genetic diversity in invasive populations could be explained by the genetic characteristics of the native sources from which they might be derived. A phylogenetic analysis confirmed two lineages of the invasive M. galloprovincialis, i.e., the NW Atlantic and the Mediterranean lineages. We found no evidence of genetic structure in the invasive range of M. galloprovincialis in Chile, most probably because of its recent arrival. We did, however, detect a spatial mixture of both M. galloprovincialis lineages at sampling locations along the Chilean coast, giving rise to higher levels of genetic diversity in some areas compared to the population of native M. chilensis. The coastal area of the invasion is still small in extent (~100 km on either side of two large ports), which supports the hypothesis of a recent introduction. Further expansion of the distribution range of M. galloprovincialis may be limited to the north by increasing water temperatures and to the south by a natural biogeographic break that may slow or perhaps stop its spread. The use of internal borders as a tool to minimise or prevent M. galloprovincialis spread is therefore a genuine management option in Chile but needs to be implemented rapidly.

Scratch circles and circular purported ammoglyphs: Novel observations from the Cape south coast of South Africa

Scratch circles, previously defined as ‘bedding plane parallel sedimentary structures formed by the passive rotation of a tethered organism into the surrounding sediment’, have hitherto been identified in the geological record from the Ediacaran to the Paleocene, as well as in modern settings. They have not met the definition of trace fossils, being passively registered by a part of a plant. Several variations of scratch circle morphology have been identified in or on Pliocene and Pleistocene deposits on the Cape south coast of South Africa, allowing for an expansion of the scratch circle temporal range. Furthermore, these novel forms require a redefinition of the term ‘scratch circle’. Anthropogenic origins need to be considered for occurrences in the Pleistocene; guidelines to assist in distinguishing such causes from typical scratch circles are presented. Scratch circles may conceivably have inspired the creation of circular patterns (palaeo-art) in sand by Middle Stone Age hominins. Evaluation of scratch circles in snow allows for subtle features to be determined. A re-evaluation of what the term ‘trace fossil’ constitutes could be considered, in order to include the term palaeo-ichnobotany.

Population-specific responses to developmental temperature in the arboviral vector Aedes albopictus: Implications for climate change.

The increase of environmental temperature due to current global warming is not only favouring the expansion of the distribution range of many insect species, but it is also changing their phenology. Insect phenology is tightly linked to developmental timing, which is regulated by environmental temperatures. However, the degree to which the effects of developmental temperatures extend across developmental stages and their inter-stage relationships have not been thoroughly quantified in mosquitoes. Here, we used the mosquito Aedes albopictus, which is an aggressive invasive species and an arboviral vector, to study how developmental temperature influences fitness across developmental stages, thermal traits, energy reserves, transcriptome and Wolbachia prevalence in laboratory-reared populations originally collected from either temperate or tropical regions. We show that hatchability, larval and pupal viability and developmental speed are strongly influenced by temperature, and these effects extend to wing length, body mass, longevity and content of water, protein and lipids in adults in a population-specific manner. On the contrary, neither adult thermal preference nor heat resistance significantly change with temperature. Wolbachia density was generally lower in adult mosquitoes reared at 18°C than at other tested temperatures, and transcriptome analysis showed enrichment for functions linked to stress responses (i.e. cuticle proteins and chitin, cytochrome p450 and heat shock proteins) in mosquitoes reared at both 18 and 32°C. Our data showed an overall reduced vector fitness performance when mosquitoes were reared at 32°C, and the absence of isomorphy in the relationship between developmental stages and temperature in the laboratory population deriving from larvae collected in northern Italy. Altogether, these results have important implications for reliable model projections of the invasion potentials of Ae. albopictus and its epidemiological impact.

Silicon photonics hybrid wavelength tunable laser diode using curved directional couplers with 145 nm tunable range

The expansion of the wavelength tunable range of wavelength tunable laser diodes is required in optical communication and sensing. Curved directional couplers (DCs) exhibit smaller power coupling efficiency fluctuations than conventional straight DCs, which reduces the wavelength sensitivity of double-ring wavelength filters. In this study, we fabricated a hybrid wavelength tunable laser diode comprising curved DCs with an improved design. This laser diode had a wavelength tunable range of 145.2 nm, which is the broadest tunable range as an external-cavity laser diode with silicon waveguides.

Signal dynamic range expansion and power supply voltage reduction for an exponentiation conversion IC

In order to compensate for the non-linearity of an electronic device, an exponentiation conversion circuit that can change the power exponent to any value has been proposed. The exponentiation conversion circuit multiplies the logarithmically converted input signal by a power exponent value to perform exponential conversion. As a result, we can obtain the power function characteristic of a power exponent value. This circuit is a small-scale circuit that utilizes the exponential characteristics of the MOSFET subthreshold region. In a conventional circuit, expansion of the signal dynamic range and reduction of the power supply voltage have been an issue. In this paper, it was confirmed by simulation that the signal dynamic range has expanded by optimizing the current density of MOSFETs. In addition, the linearity of the multiplying circuit was improved by feedback produced by the operational amplifier circuits. We proposed reducing its power supply voltage from 6.0 to 3.3 V by a new multiplying circuit that can eliminate the restriction of maximum voltage gain. Our circuit expands its signal dynamic range from 17.5 to 42.7 dB in condition of the power exponent value from 0.50 to 2.0.

Rediscovery of Actinodontum lomaense: a range extension from Sierra Leone to southern Africa

The history of Actinodontum lomaense has been marked by taxonomic revisions since its initial discovery in samples from Sierra Leone during 1984. The reassignment from the genus Docidium to the genus Actinodontum primarily resulted from pronounced morphological differences, including variations in cell size and shape, ornamentations on the cell wall, and the presence of conical teeth-like structures at the isthmus. This article reports on the discovery of A. lomaense in two locations in southern Africa, marking a significant expansion of the geographical distribution range of the genus, from the tropical regions of Sierra Leone to sub-tropical environments in South Africa and the Kingdom of Lesotho. Additionally, the preference of Actinodontum species for relatively high altitudes, observed in this study, confirms a biogeographical pattern characterising this genus. Cell dimensions recorded in the southern African samples slightly exceeded dimensions previously reported in the literature. As a result, an extention of the dimension ranges for this species is proposed. Findings presented in this article, along with physico-chemical variables measured in their habitat, contribute to our understanding of the ecological preferences and distribution patterns of A. lomaense. It also provides valuable insights into the biogeography of desmid species on the African continent.

3D Printing of Capacitive Pressure Sensors with Tuned Wide Detection Range and High Sensitivity Inspired by Bio-Inspired Kapok Structures.

Flexible pressure sensors have drawn considerable attention for their potential applications as electronic skins with both sensitivity and pressure response range. Although the introduction of surface microstructures effectively enhances sensitivity, the confined volume of their compressible structures results in a limited pressure response range. To address this issue, a biomimetic kapok structure is proposed and implemented for constructing the dielectric layer of flexible capacitive pressure sensors employing 3D printing technology. The structure is designed with easily deformable concave and rotational structures, enabling continuous deformation under pressure. This design results in a significant expansion of the pressure response range and improvement in sensitivity. Further, the study purposively analyses crucial parameters of the devised structure that affect its compressibility and stability. These include the concave angle θ, height ratio d1 /d2 , rotation angle α, and width k. As a result, the ultimate pressure sensors demonstrate remarkable features such as high sensitivity (≈2.38kPa-1 in the range of 0-10kPa), broad detection range (734kPa), fast response time (23ms), and outstanding pressure resolution (0.4% at 500kPa). This study confirms the viability of bionic structures for flexible sensors, and their potential to expand the scope of wearable electronic devices.

Range and assortment policy for “Juice products” subcategory of three retail chain stores in Moscow

The purpose of this article is to analyze the indicators of the assortment of juice products in the stores of three retail chains, namely in the Auchan, Globus, and Perekrestok stores, as well as to identify the directions of their assortment policy in this subcategory. It has been established that the assortment of the subcategory of juice products is represented by 12 types, 44 trademarks, and 301 trademark modifi cations, which makes it possible to classify it as comprehensive. 32% of the branded assortment consists of brands. The majority of juice product brands are represented by industrial trademarks (40 TMs) and only 4 trademarks are private labels (approximately 30% of the total number of brands). The coeffi cients of completeness, depth, and stability are average. The assortment of the Auchan store is characterized by the greatest completeness, depth, stability, and rationality, while the Perekrestok store — by the smallest, which is due to differences in the retail space of these stores. The degree of renewal of the assortment of juice products is almost 25% of the actual assortment. The directions of the assortment policy of the examined stores are as follows: in Auchan — the expansion of the product range and deepening of the brand assortment, as well as the stabilization of the actual assortment and updating through trademarks and their modifications; in the Globus hypermarket — the reduction in the variety of types and a moderate expansion of the brand assortment, as well as its updating; in the Perekrestok supermarket — a moderate deepening, the reduction in the type and brand assortment, and its moderate updating.

Theoretical and experimental study on the fatigue property of material extrusion products and improvement by using vibration machining during manufacturing process

Nowadays, material extrusion (ME) is one of the most popular additive manufacturing technology, which offers a new way of manufacturing parts with specific complex geometry and mechanical properties. However, with the expansion of the application range of ME products, it is urgent to investigate their fatigue property so as to ensure the reliability and safety. In this paper, the damage mechanical fatigue life prediction model of ME products considering void defects was established. Fatigue test specimens built with different processing parameters were then fabricated, and tensile fatigue tests were carried out under different stress levels. In addition, a novel method, utilizing vibration during ME process, was proposed to improve the built products’ fatigue property, and corresponding theoretical and experimental investigations were performed to reveal the influencing mechanism of the vibration utilized. The results showed that the proposed model was validated by comparing the theoretical predictions with the experimental measurements. As layer height and printing speed were increased, the fatigue life of ME specimens dropped, while it rised with the increasing extrusion temperature. The built products’ fatigue life could be improved obviously by using vibration.

Strain measurement with adaptive local feature extraction method based on special fiber OFDR system.

The optical fiber distributed strain sensor based on the optical frequency domain reflectometer (OFDR) preserves its dominant position in short-distance measurement fields with high spatial resolution, such as biomedical treatment, soft robot, etc. However, owing to the weak intensity of the Rayleigh backscattered signal (RBS) in the single-mode fiber (SMF) and complex computation, the large strain changes cannot be precisely and rapidly demodulated by the traditional cross-correlation method. In this work, the OFDR with backscattering enhanced optical fiber (BEOF) is proposed and demonstrated for fast and large strain measurement. By enhancing the RBS amplitude, the signal-to-noise ratio (SNR) is improved, resulting in a higher similarity between the reference signal and test signal, which is beneficial for the expansion of the strain measurement range. Moreover, the adaptive local feature extraction and matching (ALFEM) algorithm is presented and demonstrated, which replaces the traditional cross-correlation method for strain demodulation and fast measurement. On account of the enhancement ratio of BEOF, the dominant characteristic data segment can be extracted from whole wavelength data. In the experiments, the enhancing ratio of BEOF is designed as 10, resulting in the spatial resolution reaches 400µm and the strain measurement range is greatly increased to 4800µɛ. Further, the effectiveness of the ALFEM algorithm has been verified, in which the strain demodulation time is approximately 25% of that of the traditional method. This scheme fully exploits the enhancement characteristic of the BEOF and is also applicable to the systems based on other types of BEOF, different strain changes and sensing distances.

Complex Characteristics and Control of Output Game in Cross-Border Supply Chains: A Perspective of Inter-Chain Competition

In this paper, an output dynamic game model of intertwined supply chains operating in two different countries is established. The Nash equilibrium point of the model and its stable region are obtained using nonlinear dynamic principles. The complex properties of the system, such as stability, period-doubling bifurcations, and chaos, are investigated using numerical simulations. Our results suggest that the level of output and the system’s profits undergo bifurcation and chaos with an increase in the output adjustment speed. An interesting phenomenon occurs in that higher tariffs lead to the expansion of the stable range of the supply chain in the product-exporting country. The chaotic behavior of the system is sensitive to the value of the initial level of output. In supply chain competition, each supply chain firm should make suitable adjustments to the speed of output. To maintain the stability of domestic markets, excessive tariffs should be avoided. It is essential that each supply chain firm evaluates the potential impacts of different initial output values when making initial decisions. Using the method of delayed feedback control, the chaotic behavior of the system can effectively be controlled. These findings offer valuable and novel insight into inter-chain competition in supply chain networks.

Effects of Different Levels of Physical Damage Combined with Fungal Induction on Agarwood Formation

As wild Aquilaria sinensis resources are exhausted and protected, China has established a huge number of plantations of Aquilaria trees and developed artificial induction techniques. However, the current output and quality of artificial induction technology have not yet met the expected results. It has been found that high-oil-containing agarwood may contain particular fungal stains associated with agarwood production. To enhance the quality of agarwood, we recovered and characterized three highly active fungi from high-oil-containing agarwood and inoculated them onto A. sinensis trees using two traditional physical methods. The results showed that fungi extracted from high-oil-containing agarwood can effectively increase the yield and quality of agarwood. During the agarwood formation process, parenchyma cells, xylem rays, and axial parenchyma cells in the xylem gradually undergo apoptosis, thereby promoting the expansion of the color range of agarwood. Nine months after the treatment, the alcohol-soluble extract content in agarwood reached the standard specified in the Chinese Pharmacopoeia (10%), and the proportions of sesquiterpenes and chromones in each treatment were 55.82%, 58.31%, 62.65%, 70.97%, and 13.71%, respectively. These results indicate that fungal induction has a positive impact on the quality of agarwood. In addition, compared to drilling and fungus combined induction, “burning holes and fungi” combined induction demonstrates better results and can further improve the yield and quality of agarwood.

Expansion of Measurement Range of Low-Cost Ethernet-Based Temperature Sensing System Using Long-Period Fiber Grating

Expansion of Measurement Range of Low-Cost Ethernet-Based Temperature Sensing System Using Long-Period Fiber Grating

PROMOTION OF TRANSCARPATHIAN TOURISM SERVICES AS AN ACTIVATOR OF THE REGION'S DEVELOPMENT

Objective. The objective of the article is to determine the significance, directions and consequences of the promotion of tourism services in Transcarpathia as an activator of the region's development. Methods. The following methods and techniques of cognition are used in the research process: theoretical generalization and comparison, analysis and synthesis, induction and deduction, generalization and systematization. Results. The importance of promoting tourism services in Transcarpathia as an activator of regional development lies in the fact that without high-quality promotion, regional tourism services will not be able to reach the appropriate level of development and gain a competitive position, which for this region implies the loss of economic and social opportunities to use natural and recreational opportunities and resource potential. Promotion of tourism services is one of the most difficult and important stages of activity in the tourism market. For the successful promotion of tourism services, the following preliminary activities and conditions must be ensured: development of interesting tours, supported by a number of services; organizing the sale of tourism products taking into account the characteristics of the tourism market; searching for new opportunities, developing new tourism offers; updating the tourism product by improving services, taking into account fashion, market trends; taking into account the price-quality ratio of tourism products; increasing market share by improving product quality and attracting qualified employees; attracting investments; expansion of the tourism product range; marketing and advertising strategies, etc. As for specific areas for intensifying the promotion of tourism services in Transcarpathia, at the regional level a regulatory document “Program for the development of tourism and resorts in the Transcarpathia region for 2021 – 2023” was adopted, providing for the implementation of directions for promoting tourism services in Transcarpathia as an activator of the development of the region through solving a number of problems. At the regional level, specific tasks are solved to promote tourism services in Transcarpathia with the help of such tools as participation in exhibitions, forums, conferences, PR (production of information publications and films about the tourism and recreational industry of the region), formation of a tourism brand (image of the region), attraction and preparation personnel for organizing tourism services. The consequences of the implementation of the presented directions for promoting tourism services in Transcarpathia is that they contribute to the development of the tourism industry and its infrastructure, which covers hotel, restaurant, transport, trade, entertainment and other areas of economic activity in the region. The tourism industry ensures an increase in employment levels, the preservation and development of cultural potential, the preservation of an environmentally friendly natural environment, and also contributes to the harmonization of relations between different countries and regions.